Henan Excellent Machinery Co., Ltd
+86-18337370596

Development And Design Of High Efficiency Differential Mineral Sizers

May 16, 2023

Mineral sizers are a type of roll crusher. The working surface is cast with regular arrangement of teeth. When the two rollers rotate opposite each other, the material falling from the feed port is snapped into the crushing chamber, so as to be broken. Mineral sizers play a major role in chopping, extrusion breaking, bending breaking, impact breaking, etc. This project is based on the demand for a crushed wet nickel laterite ore. The raw ore is sifted into the mineral sizers with an inlet size of -400mm and an discharge size of -100mm. The required production is 500tm. Mineral sizers with diameter of 1200mm, roll length of 1200mm and rotation speed of 65r/min can meet the production and particle size requirements.

The main parameters include basic structure parameters and main working parameters. The two parameters are interrelated and restricted. For example, the shape and layout of the roller teeth have an impact on the size of the discharge and the output, and according to the required output to choose the appropriate motor power and speed, all of the roller distance and the layout of the roller teeth put forward requirements.

1.1 shape and arrangement of roll teeth

Considering that the shear strength of the material is much smaller than the extrusion strength, the material is broken, broken much easier than the extrusion crushing, and save work, so the shape of the roller teeth for the eagle mouth shape (four prism), in order to facilitate the crushing material. Due to the high water content of the material, there is the possibility of sticking roller, the use of two roller teeth staggered arrangement, and add comb teeth on both sides of the box, can timely clean up the sticking material. The cloth roller with adjustable center distance can adjust the size of the discharging particle size, and also can make the two toothed rollers comb each other while crushing materials to avoid sticky material. The layout of roll teeth and the arrangement of backlash should meet the requirements of discharge particle size, but also consider the crushing expansion of ore, so the clearance of roll teeth should be slightly larger than the discharge particle size. Roll tooth arrangement. 1.2 according to the required output, if the material is 100% filled in the discharge path (the space rotated by the roll gap of two teeth), the volume of this space is the discharge volume.

Where, r is the radius of the root circle of the tooth roller, 0.52m; e is the width of discharge port, 0.1m; l is roll length, 1.2m; v, is the volume of roll teeth. The three-dimensional software is used to form the solid roll teeth, and the volume of a single roll teeth is measured to be 0.2×103m3, and the total number of teeth of two rolls is z=288, so v,=57.6×10-3m3,v=0.37m3. Thus, the rotational speed n= 20.48r /min at 500t/h output can be calculated by formula (1).

mineral sizers

The mineral sziers calculation results show that the rotation speed of at least 20.48rmin is required to achieve the yield of 500th. It is practically impossible for the material to fill the discharge path by 00% at such a rotating speed. The essence of 00% material filling and discharging path is that the material fills the gap and tooth between two rolls. If the discharge path is full of material, the tooth roller only has extrusion effect on the material, no crushing effect. In fact, the material falling speed is slower than the linear speed of the tooth roller, which makes the tooth top of the two rollers, there is a gap between the teeth, that is to say, the material is not 100% filling and discharging path. But this is good for the crushing of the material, so that the material can be split between the teeth. The rock has the property of crushing, and the crushing is completed in the non-material path, so the material should not be 100% filled in the discharge path. Therefore, the actual speed should be higher than 20.48rmin, so as to meet the output of 500h. Formula (1) is introduced into the correction coefficient k, which is affected by the saturation of feeding material, the characteristics of the material itself, the length of the cloth roll of the material, the composition of the feeding size and the crushing ratio. According to the empirical formula of double-smooth roll crusher, k=0.40.6 is generally taken, and here =0.4 is taken to make the output have a certain margin. 

The speed can be modified to n=51.19r/mino 2. The transmission sequence of the proposed machine in the basic structure form is: Motor → belt → reducer driving roller → differential device → driven roller. Taking into account the particularity of the material is wet and soft, easy to stick roller, adopt the form of comb teeth. Because of the gap, the two roller teeth staggered together can rotate freely without collision. In order to avoid the blocking of the material in the gap and to increase the tearing effect between the tooth roll and the material to facilitate the breakage, the two teeth roll is used to rotate asynchronously, which is called differential rotation. The differential mechanism makes the master and driven roll move towards the differential and transfers the mineral sizers from the active roll to the driven roll. The output can be guaranteed by choosing the driving roller speed of 60r/min and the driven roller speed of 52rmin. Considering that the load type of the crusher is impact load, a joint narrow v belt drive is adopted between the motor and the reducer, which has small structure size and large transfer power, and can realize the flexible transmission between the motor and the load.


Related Products