Henan Excellent Machinery Co., Ltd
+86-18337370596

Fracture Force And Phase Advance Of Mineral Sizers

Apr 04, 2023

The shearer cutting resistance formula summarized by the former Soviet Union experts was introduced into mineral sizers. The equilibrium relationship between the cutting force and the supporting reaction of the material particles under the condition of transient stable support was obtained. A generalized breaking force expression with random discrete properties of the material particles was derived: Then, the random discrete characteristics of material particles based on production capacity are discussed, and the recursive formula of particle passenger-weight satisfying D3 distribution and the expression of interval particle efficiency are given. Secondly, the probability coefficient of time pulse load of the particle material is analyzed, and the phase advance of the fine particle material under the condition of stable support and double bow thick cutting is discussed, and its relationship with the production capacity and power consumption is discussed. Finally, the matrix expression of pulse load with random discrete properties of granular material is given. It has important theoretical significance and practical application value for the research and development of fine particle material crusher.

mineral sizers

The mechanical model of any mechanical system is the basis of analyzing the dynamic, kinematic and static characteristics of the mechanical system. The mineral sizers are broken by random and discrete materials. This makes it a challenge to build mineral sizers mechanical model. It is because of this that it can better reveal the breaking mechanism of the crusher. Foreign scholars use discrete element method and discrete element analysis software to simulate the size of the crushing force. The process is as follows: Through the experiment measured the physical properties of the material as the simulation parameters and then set the particles to replace analog crushing process, this method cannot be measured tangential stiffness and normal stiffness between particles, only through the simulation experiment results of the process of compressive strength and the actual estimate is obtained, the results of experiment and discrete element simulation in the process of material particle size do not have random discrete, So this method has obvious shortcomings. Therefore, considering the random and discrete properties of mineral sizers, it is of great theoretical significance and practical value to study the kinetic, kinematic and static properties of mineral Sizers and develop new products.

Mineral sizers The broken material has the random discrete property. Assuming that the granular material is a spherical material with a specific particle size, when the radius (k) of the spherical material is determined, its position in the crushing chamber is determined, as shown in Figure 1. As long as certain conditions are met, the cutting gear starts cutting from point A, reaches the maximum cutting depth at point B, and completes the cutting process at point C, the cutting force of the material at every instantaneous is balanced with the supporting reaction. For example, when the cutting gear reaches point B, the supporting condition is that the supporting reaction force N,N,Nm forms a stable triangular support, and is balanced with the cutting force P. When cutting tooth cutting to point B, maximum cutting depth, the instantaneous tangential cutting resistance can be used in the former Soviet union scholar summarized coal winning machine cutting resistance formula: Pa = psK, K2K, h (0.25 + 0.018 + 0.1) F]; K = 0, 1,... kN:p - contact strength of cut rock, MPa, rock firmness coefficient f and contact strength p, the corresponding relationship is shown in Table 1. When the hardness coefficient (i.e., Platinell hardness coefficient) exceeds the value in Table 1, the contact strength can be calculated as P=44×f; K, influence coefficient of cutting type, K=1.5; K2 is the influence coefficient of cutter geometry, K=1232; K, is the influence coefficient of tool head size, K=l.25; One line spacing, mm; h cut depth, mm; F Tooth wear area, generally F=(15~20)mm2. Lateral force of single tooth cutting material: P=KPeg=[c,(c2th)tc3]+(hh)}Pe; K = 0, 1,... In formula 8(2) : c1 and c2c tooth arrangement influence coefficient, in order,c =1.4,c2=0.3,c 0.15. When the material to be broken Prinell hardness coefficient, cut depth h, cut line spacing. When it is determined, its cutting resistance load is a set of determined constants, that is, its generalized load: P=PP.PM=0,1,.8 where: P a horizontal component: P a vertical component; Me, one torque; We, one power. What should be emphasized here is that the former Soviet Union scholars summed up the load formula based on a large number of test results, and after a long time of application, it has been proved that the calculation results can be in good agreement with the actual test results. In addition, the most prominent feature of this formula is that the Platinell hardness coefficient "only needs to test the compressive strength of the material to be crushed. Compared with the test Bond work index, it is simple and reliable. At the same time, it avoids the influence of the index value in Holmes formula. 2.2 Random Discrete Probability Characteristics of particle bulk Density 2.2.1 Decomposition of Crusher capacity. The cutting resistance and the time pulse load of mineral sizers are both single-tooth. Therefore, it is necessary to assign mineral sizers the crushing task to a single tooth. Qx10Q,=3600×0xZ(4), where :Q, the crushing production task of a single tooth is particle bulk density, (cms): the production capacity of a crusher Q, (h): the number of crushing teeth of a crusher Z; p -- Density of material to be crushed, (gcm). In order to facilitate the discussion, the following analysis of random discrete pulse load takes 2PGC-307 prototype crushing test as an example, which not only gives qualitative conclusions, but also gives quantitative results, which can not only directly test the correctness of theoretical analysis, but also carry out error analysis. The complete prototype parameters and material characteristic parameters, the specific reference of parameters and the calculation results are given in the reference.


Related Products