In the middle and late 1980s, mineral sizer crusher rose with the development of graded crushing technology abroad and became a new crushing equipment. The crushing teeth are arranged in spiral on the tooth roller, and the material is broken by rotating parallel tooth rollers opposite or opposite each other. Because the equipment is only larger than the product size of the material crushing, and less than the product size of the material directly sieve, so it is also called screening crusher. mineral sizer crusher makes full use of the characteristics that the shear and tensile strengths of materials are far less than the compressive strength, and uses the shear and tensile forces to crush materials 1. Therefore, mineral sizer crusher has the characteristics of low energy consumption, small over-crushing rate, simple structure, convenient maintenance and so on. It is one of the indispensable crushing equipment in many large coal mines and open-pit mines in China.
1. Existing problems of beam crushing device
The 2PGC-1370 mineral sizer crusher is selected by a mine in China. The installed power is 2×250 kW, the crushing roller diameter is 1370mm, the production capacity is 2 000 t/h, the maximum feeding particle size is 1 500mm, the discharging particle size is 300 mm, and the crushing material is limestone.
After commissioning and running of the equipment, the crushing roller crushing force is large, the material occlusal is smooth, and the output reaches the standard. However, after 3 months of use, the fixed bolts of broken beams broke frequently, and were replaced once every 1 to 2 months on average. Later, the strength of the broken bolt was changed from 10.9 to 12.9, and the bolt broke again after being used for about two months.
1.1 Structure of beam crushing device
Mineral sizer crusher consists of motor, hydraulic coupler, reducer, toothed coupling, crushing roller, box and crushing beam. Its structure is shown in Figure 1. The upper area between the teeth of the two crushing rollers is the primary crushing area, which is mainly responsible for crushing large materials through the crushing roll teeth occlusion. The two triangle areas between the lower crushing roll and the crushing beam are the secondary crushing zone. The secondary crushing of materials can be realized through the occlusion of the crushing roll teeth and the crushing beam teeth. Through two crushing, crushing ratio can reach about 6:1, uniform discharge particle size.
Mineral sizer crusher is a key component for realizing secondary crushing, improving crushing ratio and controlling particle size. The beam breaking device consists of a broken beam body, broken beam teeth and a particle size adjusting device, and its structure is shown in Figure 2. The broken beam is fixed on the box with bolts, and the teeth of the broken beam are connected with the broken beam through a flat key and fixed with bolts. With the wear of the crushing teeth, the discharge particle size will also increase. At this time, the discharge particle size can be adjusted by the particle size regulating device (see Figure 3). Adjustment method: By twisting the long bolt, lift the broken beam to the appropriate height, then relax the long bolt, add the gasket, adjust the broken beam, and then fix it with the fixing bolt. Namely, by reducing the distance between the crushing roller and the crushing beam crushing chamber to compensate the crushing tooth wear amount, so as to meet the set particle size requirements again.
1.2 Check the strength of bolts
In view of the fixed bolt fracture, it is considered that the broken beam is caused by too much force. The bolt adopts M36 high-strength bolt. In order to prevent the broken beam from loosening, a larger preload F is selected. Is equal to 350 000 N. The force diagram of the broken beam is shown in Figure 4.
2 Improvement Measures
After the bolt is broken, if it is not treated in time, the broken beam will be displaced, and the teeth of the crushing roll and the teeth of the crushing beam will interfere with each other, causing the teeth of the crushing roll to wear too fast or even break. Therefore, when encountering refractory or dense materials, the mine needs to be extra cautious. Once the load current is a little larger, the feed speed should be reduced immediately or the machine should be shut down, and the bolts should be checked every day, and the problems should be replaced in time. A number of approaches were tried to solve this problem, but the simple, practical wedge-fixing method was chosen, as shown in Figure 5.
The cabinet space of the original mineral sizer crusher is used to increase the support frame and wedge iron at both ends of the cabinet. Wedge iron and support frame fit surface with 1:12 inclination, using small inclination, wedge tight more reliable, not easy to loose. The support frame is solidly welded to the box, and the wedge iron is used to tighten evenly between the broken beam and the support frame. After the bolts are firmly fixed, the wedge iron is spot welded to the support frame. When the particle size needs to be adjusted, it is only necessary to grind the spot welding of the wedge block, raise the broken beam, and then tighten the wedge and screw on the fixing bolt after re-leveling. The wedge structure makes full use of wedge iron to bear the horizontal crushing force, and the fixed bolt only receives the vertical force without the horizontal shear force, which greatly improves the reliability of bolt connection.
