Our secondary sizer for coal mining boasts significant advantages in terms of durability. All its core components are made of high-strength and wear-resistant materials.
The broken tooth plates are made of wear-resistant and impact-resistant alloy steel. They are processed through precise casting and heat treatment processes, with a surface hardness of up to HRC 50-55 and an impact toughness of ≥ 48J/cm². They can effectively resist the wear and impact from coal and gangue. The service life of a single set of tooth plates is no less than 3 years or an overburden volume of 600 million tons.
The tooth roller shaft is made of 42CrMo alloy steel forgings. After quenching and tempering treatment, it has both strength and toughness, capable of withstanding long-term heavy-load operation.
The bearings use large clearance self-aligning roller bearings, combined with a dual labyrinth seal + frame fluororubber oil seal protection structure, effectively preventing dust and moisture from entering. The service life of the bearings is over 30,000 hours.

The core working principle of the Ssecondary sizer for coal mining is bisecondary sizer for coal mining is bnism of shearing and stretching.

● After the equipment is started, two explosion-proof motors drive the double toothed rollers to rotate in opposite directions through the transmission system. The spirally arranged teeth on the toothed rollers form an interlocking structure.

● When the raw coal that has undergone primary crushing enters the crushing chamber, it is first precisely gripped by the tooth tips. The relative movement of the two tooth rollers exerts a shear force, and at the same time, the stretching effect produced by the tooth shape design causes the material to break along natural fractures.

● Particles with a size smaller than the gap between the toothed rollers are directly sorted out through this process. For the materials larger than the gap, they are continuously sheared and broken until they reach the preset discharge size. This ultimately achieves the integration of efficient crushing and sorting.

Coal Secondary Sizer Drive Device

Drive Device

Two independent drive units, each drive units includes: motor, high-speed end coupling, gear box, low-speed end coupling. The high-speed end coupling uses a hydraulic coupling to connect the motor to the gearbox. The gearbox adopts parallel shaft helical gear structure to meet the requirements of power transmission, speed ratio and torque under extreme load of the Secondary Sizer For Coal Mining .

Toothed Roller

Toothed roller can be divided into Primary Secondary Sizer For Coal Mining Toothed Roller and Secondary Secondary Sizer For Coal Mining Toothed Roller. Easy installation and disassembly of the Secondary Sizer For Coal Mining tooth head, which can significantly reduce the maintenance time and lower the maintenance cost.

Housing

Secondary Sizer For Coal Mining housing is designed as a rigid host frame, and the housing is made of cast steel and connected by high strength bolts. Wear-resistant plates are installed around the inside of the housing, and comb shaped wear plates are installed on both sides of the housing to prevent excessive material from adhering to the crusher tooth rollers.

Side Plates

The side plates of the Secondary Sizer For Coal Mining are integrally formed through high-quality casting technology, ensuring a stable and reliable structure. After precise processing by a high-precision CNC lathe, the side plates achieve strict mating accuracy during installation. This design not only extends the service life of key components but also ensures the smooth operation of the entire machine, providing continuous support for the equipment under high-intensity working conditions.

Lubrication Device

Secondary Sizer For Coal Mining adopts centralized automatic lubrication system, it can be more oil filling times, oil filling time Settings, reliable to ensure the effective and reliable lubrication of each part. Automatic control of oil supply interval time, oil supply pressure is large, oil supply speed is fast, the bearing is fully lubricated effectively, so that the core part of the teeth roller bearing to achieve good lubrication, greatly extend the service life of the teeth roller.

Running Gear

The tramming device is installed at the bottom of the Secondary Sizer For Coal Mining and driven by a motor to move along a track to the maintenance access, facilitating easy maintenance and avoiding disassembly. This design allows the equipment to move smoothly between the operating and maintenance areas, reducing manual labor and minimizing downtime during maintenance, thus improving operational efficiency.

The feeding granularity of primary sizers is less than or equal to 1500mm and the discharging granularity is less than 300mm. The arrangement of crushing tooth shapes and tooth shapes are arranged by special spiral tooth shapes. The crushing teeth are cast from abrasion resistant and impact resistant alloy steel. Primary Sizer toothed roller has a unique and novel tooth design structure with deep spiral distribution for high productivity. The passing cavities are formed between the two toothed rollers and the side plate body for screening and crushing materials respectively.

Primary Sizers Toothed Roller

The Feeding size of Secondary sizer less than or equal to 300 mm (a small amount of 400mm is allowed), and the discharging granularity is less than 50mm. The connection form of the teeth plate adopts a single dovetail groove, which is complementary to the bevel of the insert clamping block, and then the crushing tooth plate is installed on the fixing seat of the teeth plate, formed a surface to surface connection, which is tightened and pressed by high-strength bolts. The function of the bolt becomes a fixed insert clamping block, avoiding the problem of the fixed lock bolt breaking, teeth plate falling off or difficult to disassemble and replace.

Secondary Sizers Toothed Roller

01/

Easy To Move
We adopt a compact modular structure, reducing the floor area by 30% compared to equipment with the same production capacity. The equipment can be disassembled for easy transportation and on-site assembly, which is suitable for the production characteristics of frequently relocated open-pit mines, thereby reducing the costs of site construction and equipment relocation.

02/

Anti-clogging
We incorporate the spiral toothed design + reverse gear function, which can automatically remove the adhered materials generated during the coal crushing process, preventing the discharge port from getting clogged. Even when dealing with coal with a high clay content, it can maintain a stable production capacity.

03/

Low-temperature Resistant
We have equipped the machine with low-temperature resistant motors and an insulation lubrication system. It can start and operate stably even in an extremely cold environment of -45℃. This design perfectly suits the winter production in northern coal-producing areas such as Inner Mongolia and Xinjiang, solving the problem of equipment startup in low-temperature conditions.

04/

Long Operating Cycle
The overall machine overhaul cycle of our product is ≥ 8 years. The lifespan of the main structural components is ≥ 20 years. The bearing sealing protection has been upgraded. It is compatible with the 24-hour continuous production mode of the coal industry, reducing downtime for maintenance and improving the effective operation rate of the equipment.

05/

Intelligent Adaptation
We are equipped with PLC control system and multi-dimensional sensors, which support connection with the coal mine centralized control system. It enables remote monitoring, automatic adjustment and fault warning, and is suitable for the intelligent and unmanned production trend in the coal industry.

06/

Low Energy Consumption
We adopt the low-speed high-torque operation mode, with the unit energy consumption as low as 0.12 kW・h/t. Compared with traditional equipment, it saves more than 35% of energy, meeting the cost reduction and efficiency improvement requirements of the coal industry. Long-term operation can significantly reduce electricity expenses.

Contact Us For Best Price

Submit your requirements and talk with one of our technical engineer about your project.

Send Inquiry Now

A high quality mechanical products, must have excellent tooling equipment. In order to ensure its accuracy and meet the needs of large orders. Henan Excellent Machinery Co.,Ltd owns 140 sets of professional equipment, including Five-axis Gantry Machining-center, CNC Boring And Milling Machining Center, Vertical Machining Center, Vertical CNC Machining Center, Gantry Machining Center, Laser Cutting Machine, Laser Pipe Cutting Machine, Welding Robot Workstation, Lengthen Lathe, CNC Horizontal Machining Center, etc. Advanced processing and manufacturing equipment including Environmental Spraying Room and Heat Trea equipment and ultra large Surface Heat Treatment.

Left And Right Side Plate Blanking Process

Mineral Sizers Front And Rear End Cover Machining Process

Front And Rear End Cover processing

Mineral Sizers Left And Right Side Plate Machining Process

Left And Right Side Plate processing

Mineral Sizers Teeth Ring Internal Surface Machining Process

Teeth Ring Internal Surface processing

Teeth Base Processing

Teeth Roller Heat Treatment

At present, EXCT has fully passed ISO9001-2008 international quality system certification, complete quality system make sure that from the product development and design, production, procurement and supply to sales and service process has been effective quality controlled.

EXCT has a rigorous and skilled inspection team to ensure the success of product quality control. The quality inspection department has a strict testing process that runs through the stages of raw material procurement, production, and installation to ensure that every piece of equipment delivered to customers is qualified.

Mineral Sizers Currency Test When Running

Current Detection

Voltage Detection

Shaft Temperature Detection

Vibration Detection

Noise Detection

Ultrasonic Flaw Detection

Hardness Detection

Coating Thickness Detection

Our Secondary Sizer For Coal Mining covers more than 20 countries and regions all over the world. They are mainly used for crushing raw coal, coal gangue, lignite, coke, topsoil and other materials, and are used in coal-related industries such as thermal power plants, coal mining, coal washing plants and so on.

Submit your requirements and talk with one of our technical engineer about your project.

Get The Most Suitable Product Solution And Quotation For Free!!!

Secondary Sizer For Coal Mining are customized for each application material to provide the best configuration and meet all your requirements.engineers.

Primary Secondary Sizer For Coal Mining s Technical Specifications
Model	2PLF800	2PLF1000	2PLF1200	2PLF1500
Teeth Roller Dia (mm)	800	1000	1200	1400
Roll length (mm)	1500-2500	1500-3000	1500-3000	2000-3500
Max feed size (mm)	800	1000	1200	1500
Output size (mm)	≤300	≤300	≤300	≤300
Capacity (t/h)	≤2000	≤3500	≤6000	≤10000

Secondary Secondary Sizer For Coal Mining s Technical Specifications
Model	2PLS600	2PLS800	2PLS1000	2PLS1200
Teeth Roller Dia ( mm )	600	800	1000	1200
Roll length(mm)	1000-2500	1500-3000	2000-3500	2000-4000
Max feed size (mm)	200	300	350	400
Output size (mm)	50-80	50-100	50-120	50-140
Capacity ( t/h )	250-800	500-2000	600-3000	800-4000

Note: Tooth configurations vary depending on the material type, infeed size and discharge size.

Configuration information is typical values for reference. Please contact our technical engineers for more assistance with equipment selection.

1. Which material to be crushed:______
2. Handling capacity:______t/h.
3. Bulk material density: ______t/m3
4. The material compressive strength:______Mpa
5. The material HGI (hardgrove grindability index) range:
6. Material particle distribution percentage?
7. Max. grain size of the feeding material: ______mm
8. What is the grain size of the finished product after crushing?
9. What equipment is used to feed the material into the sizer?
10. What equipment is used to discharge the material from the sizer?
11. As we know,the sizer should form a system with other equipment, do you have preliminary design or hand-drawn sketch? If have, please send it to our engineer for reference.