Inclined screens for aggregate is a kind of screening equipment, which is suitable for the coarse, medium, fine and fine screening of ore and other materials. Its novel structure, low noise, large processing capacity, stable operation and high screening efficiency are widely used in many industries, providing great convenience for people's production and life. But the Incline screen for aggregate has some glitches over time, Let's take a look at common failures of Incline screens for aggregate and how to deal with them.
Incline screen for aggregate material flow anomalies
Cause: Screen box stiffness is insufficient, there is a critical frequency, the connection bolt has been loose, even to the extent of the surface vibration loose, the horizontal level of the screen box did not find the right, appropriate to improve the height of the screen box, fastening bolts, support spring steel is too large or damaged, screen surface damage, The uneven flow of materials on the Incline screen for aggregate will result in abnormal flow of materials on the screen surface. In addition, if the material moves too slowly on the screen surface, it will result in increased material accumulation on the screen surface, making the Incline screen for aggregate operate at high load. It will also lead to abnormal flow of materials.
Treatment method: we can adjust the height of the support, adjust the spring, and adjust the screen surface, the vibrating screen for uniform, stable feeding, appropriate to adjust the vibrating screen vibration force, the running speed of the material, so as to abnormal material flow.
Cause: Inclined screens for aggregate screening quality is poor, mostly because of improper operation, too much water content of the material, the material contains water, the material is easy to adhere to the screen surface. When the water continues to increase, it will make the sieve hole clogged, sieve load large place blocked first, like the feeding end. If the moisture content increases, the fine grained material itself will be bonded into a large grain or adhere to the surface of the coarse grained material, and will remain in the sieve product can not be screened out. All of these phenomena interfere with the Incline screen for aggregate screening. In addition, the material is too thick, the tension of the screen is not appropriate, the belt is too loose will also cause the vibrating screen screening quality is not good.
Treatment method: Strictly follow the operating instructions for Incline screen for aggregate, strictly control the water content of the material, do not feed too much, adjust the tension of the screen, properly tighten the belt, Keep the Incline screen for aggregate at a steady frequency with an appropriate amplitude, so that it runs in order to achieve the sieving effect.
The Incline screen for aggregate noise is excessive
Cause: this situation may be what is the key parts inside the vibrating screen damage, or the bolts of the relevant parts loose, but also more important parts, such as bearing damage, beam fracture and spring damage, such as the occurrence of this situation may also be caused by our neglect of the maintenance work of the vibrating screen.
Solution: When this happens, we should immediately stop running the shaker and find out the problem in time. Timely tightening of bolts, timely replacement of damaged bearings, beams, springs and other accessories, in addition to the future production process to do a good job of equipment maintenance, so as to avoid the occurrence of failures, prolong the Incline screen for aggregate life.
Incline screen for aggregate does not start or has low amplitude
Cause of failure: When the Inclined screens for aggregate decreases in amplitude or fails to start, it is usually due to damage to the internal vibrating motor, which will not provide a power source for the Incline screen for aggregate, affecting the amplitude of the shaker and its normal starting. Secondly, electrical components damage, insufficient voltage, vibrator failure, residual material is too much, the grease in the vibrator thickened and caked, will also cause the occurrence of this fault.
Solution: If the fault is caused by vibration motor damage, we should timely replace the motor, electrical components damaged to replace electrical components, voltage is insufficient to change the power supply, vibrator failure we need to timely repair, if it can not be repaired, we also need to replace. When there is too much residual material, we should clean it up in time to ensure that the equipment starts without load. When the grease in the vibrator thickens and clumps, the vibrator should be cleaned in time and the appropriate grease should be added.








