Inclined Screens For Aggregate (model: 2Yah2148 Inclined Screens For Aggregate) is one of the main production equipment of mineral processing in Marine mining company. It is mainly responsible For the sorting of finished ore from 15,000 t ore silos and 20,000 t ore silos in the concentrator. Therefore, the normal operation of Inclined Screens For Aggregate directly affects the smooth progress of ore production. There are 4 sets of 2YAH2148 Inclined Screens For Aggregate (2 in use and 2 in standby) in the concentrator. After running For a period of time, Inclined Screens For Aggregate show that the axle diameter where the eccentric shaft is installed and the journal where the bearing is installed are seriously worn. Bearings and bearing seats are easy to be damaged after assembly, which cannot meet production requirements. Because the cost of eccentric shaft is 15000.00 yuan/piece, it is decided to restore its technical performance and continue to use it. 2YAH2148 Inclined Screens For Aggregate eccentric shaft shaft diameter at both ends (connected with balance wheel and belt wheel) center and bearing location axle diameter center eccentricity 3.2mm, eccentric shaft length 2487mm, maximum diameter 206mm, weight nearly 565g; Due to the need to repair the size of 110mm and 140mm, the center hole at the end of the two shafts of the eccentric shaft does not meet the machining requirements. As shown in Figure 1.
2YAH2148 Inclined Screens For Aggregate are self-centered shakers. According to the self-fixed center vibrating screen pulley center should be located between the bearing center and the center of gravity of the eccentric block, and make the pulley center line is located in the eccentric block and vibration body composite center of mass on the advantages of eccentric shaft and balance wheel structure to improve, the shaft eccentric 3.2mm to the balance wheel, specific improvements are as follows. 1.1 Improvement of eccentric shaft. Change the center of shaft diameter of eccentric shaft bearing position and the center of shaft end diameter (and the balance wheel and belt pulley connection position) into one center, solve the problem of shaft end center hole line and bearing position center hole line eccentric 3.2mm, can repair the size of 110mm, 140mm shaft diameter; The size of the improved eccentric shaft is shown in Figure 2.
1.2 Improvement of the balance wheel In order to ensure that the center of the belt wheel (which is the same center as the outside diameter of the balance wheel) and the bearing center are eccentric 3.2mm, the structure of the balance wheel is improved by changing the center of the inner hole and the outside diameter of the balance wheel to eccentric 3.2mm. Not only the eccentric 3.2mm on the original shaft is changed to the balance wheel, by marking the end face of the balance wheel, Find out the center of the inner hole and the outer diameter of the eccentric 3.2mm, and then repair the size of the inner hole. The balance wheel before and after transformation is shown in Figure 3.
2. Repair of old parts: the following two methods are used to repair 2.1 Filler welding. (1) Preheat. Preheat 110mm and 140mm in the middle of both ends of the shaft and 110mm in the inner hole of the balance wheel to keep the same temperature in the filling welding place and reduce the residual internal stress retained during cooling after filling welding place. (2) Symmetrical filling welding is adopted. In order to reduce deformation, the ideal welding sequence is shown in Figure 4.
3, Divided time, intermittent multi-layer filling welding. The area of filling welding should not be too large. 2.2 Machining. After filling and cooling, process according to the repair process requirements specified above to ensure that all dimensions meet the original size requirements. 3. Conclusion After the implementation of the above scheme, the expected results are achieved. The eccentricity between the center of the belt pulley (the same center as the outside diameter of the balance wheel) and the center of the bearing position is ensured by 3.2mm, and the center of the belt pulley is fixed between the center of the bearing and the center of gravity of the eccentric block, which guarantees the screening effect of Inclined Screens For Aggregate. To ensure the smooth progress of enterprise production, and for the enterprise to save about 60,000 yuan per year parts cost.









