Henan Excellent Machinery Co., Ltd
+86-18337370596

What Is The New Method Of Sidewall Belt Conveyor

Mar 04, 2023

The dust removal of the sidewall belt conveyor adopts the decentralized dust removal method of micro-power dust removal technology, which is independent dust removal for the relatively concentrated dust raising points, and the dust removal facilities are set up on the upper part of the belt conveyor, without taking up additional space and without any dust removal pipeline leading out of the plant; the dust collected under the belt falls directly onto the belt, without solid waste discharge, without special conveying facilities and maintenance personnel, and for the transportation of materials that do not accommodate dust Not applicable to micro-powered dust removal process; dust removal equipment is well sealed, processing air volume is small, dust removal fan motor power is 3kW, equipment noise is less than 50dB (A), lower than reaching national standards. Micro-powered de-dusting technology has 50% less running cost and 40% less investment cost than traditional decentralized de-dusting process. The dust content at the outlet of dust collector is <50mg/Nm3, which meets the standard emission; the dust concentration at the operation post is <10mg/m3, which meets the national health standard.

sidewall belt conveyor

Sealing the drop point of sidewall belt conveyor, after the drop point, in the direction of belt running, set up high efficiency settling room, dust filter, circulating separation room and sealing room in turn; high efficiency settling room, dust filter, circulating separation room and sealing room are connected to each other by two panel connectors at the bottom; one inclined guide plate is set up in the left and right of the connector, and the lower end of the guide plate is within the range of corrugated baffle, so that the materials falling from the drop The lower end of the deflector is within the range of the wavy baffle, so that the material falling in from the drop tube can be smoothly introduced into the belt groove, avoiding the dust from overflowing the belt groove and falling onto the wrinkled wavy baffle of the format belt. The lower end of the drop tube is equipped with an airflow balancing tube connected to the high efficiency settling chamber.

The panel connector organically connects the dust removal facilities such as high efficiency settling chamber, dust filter, circulation separation chamber and sealing chamber to the sidewall belt conveyor, and is a sealer for dust removal facilities and a dust trap. Its outer wall is perpendicular to the large inclined angle belt bottom plate, and the weight of the high efficiency settling chamber, dust filter, circulating separation chamber and sealing chamber is transferred to the belt frame through the support frame; the upper part of the panel connector is connected to the high efficiency settling chamber, dust filter, circulating separation chamber and sealing chamber with steel material, 150mm~300mm high; the lower part is connected to the large inclined angle belt bottom plate with rubber material, 100mm~200mm high. The width of the panel connector is the same as that of the high efficiency settling chamber, dust filter, circulating separation chamber and sealing chamber, which is equal to the width of the belt conveyor; its length depends on the length of the high efficiency settling chamber, dust filter, circulating separation chamber and sealing chamber, which is 3m~6m.

sidewall belt conveyor

The folding plate is set in the upper part of the high-efficiency settling chamber, dust filter, circulating separation chamber and sealing chamber, with the size of 300mm×200mm and the inclination angle of 15~45° from the horizontal. The circulation separation chamber is a horn shape with inclined top plate, and the inclination angle is 10~30° with horizontal direction. The flared end of the circulation separation chamber is connected to the sealing chamber, and the top of the sealing chamber is draped with rubber strips.

The deflector plate is made of steel, set inside the panel connector, the length is the same as the length of the panel connector, fixed in the upper part of the inner side of the gang plate, the tilt angle is 50~70° from the horizontal direction, the lower part of the deflector plate is set with sealing rubber strip, aiming to introduce the material and dust into the belt groove and avoid falling between the wrinkled wave-shaped gear plate and the gang plate to the greatest extent. The vertical gap between the bottom of deflector plate and the top of format sidewall belt is stuck 10mm, and the horizontal gap between the bottom of deflector plate and format sidewall belt conveyor stopper is stuck 20mm. sealing rubber strip strip diameter is 8~10mm, 4~6 layer arrangement, gap is 0.5~1.0mm.